Continue until all molding is in place. Boring small holes into the points of each outside corner joint allows you to secure the corners to the wall firmly with an extra finish nail in each hole. Smooth the crown. For pre-finished white crown molding, use paint-on white caulk to smooth the joints.
Template:Linebreak:Caulk is also appropriate for smoothing over nail holes and any other marks in the molding. Consider caulking in the gap between the top of the crown and the ceiling for a smoother appearance, if there is such a gap. Paint the crown. This step will require paint and a brush. Enamel paints are generally the best for this kind of work, and fall into two basic categories: acrylic enamel, which dries quickly and is less odorous than its counterpart, but which has a flatter finish, or alkyd enamel, which takes longer to dry and has a stronger smell, but whose deep, lustrous finish cannot be matched by acrylic paint.
Template:Linebreak:Whichever style you choose, use an angle sash brush which is preferred for its ability to paint sharp, clean lines easily , and apply your paint evenly and methodically. You can also paint the molding before you install it, but be aware that you'll have to repaint anywhere that gets scuffed during installation.
Include your email address to get a message when this question is answered. You can also buy double-sided molding, which has the decorative face on both sides. This will minimize any confusion over spatial orientation when making cuts. Helpful 0 Not Helpful 0. When measuring angles to cut your crown molding, don't forget to double check the corners of the room you are working on.
Making them in advance will save time in the long run. Buy more crown molding than you intend to use. Most home stores will let you return any unused molding, and having plenty of material in advance of the project will save you considerable grief if you end up needing extra. Always wear proper safety equipment when working with cutting tools of any kind. Helpful 2 Not Helpful 2. Be sure to ventilate the room when working with paints, thinners, or other chemicals. Helpful 2 Not Helpful 3.
You Might Also Like How to. How to. Professional Handyman. Expert Interview. More References 1. Do you put crown molding in the kitchen? Is it hard to install crown molding? What angle do you cut crown molding corner cabinets?
How do you tell the top from the bottom of crown molding? Is this the new way of installing crown molding? Thank you for your response. It is not that it looks that bad upside down but it really is bothering me because I wanted the job done properly. Unfortunately I think I am going to have to live with it because my brother insists that it is the correct way and I don't want to give him more money to redo the job.
Paul is absolutely right, you can put it any way you want of course You wouldn't want the crown to extend out onto the ceiling more than it comes down the wall. Thank you for responding to my post, Altereagle, and referring me to your website.
It was actually after viewing your website about a week ago and seeing your instructions on how to install crown molding that caused me to realize that it was probably upside down.
I have been researching this ever since. Since we don't want to tear it down, my husband and I think we will resolve this problem by adding a smaller molding or lattice at the bottom so more will be on the wall and it may appear more like we purposely had it installed upside down. I bought a house last year and the crown molding in the LR and really fancy crown in the Dining room were annoying me for some unknown reason. Then I hired a guy to install crown in the bedrooms and when we both looked up on the hallway and he said "Do you like this profile?
Because of its weight, plaster usually requires a professional installation. The cost of labor in addition to the materials can get to be quite pricey.
Plaster-covered foam is a great alternative to regular plaster. It is lighter and more flexible, making it more suitable for a DIY installation. In the end, it will appear as smooth and polished as regular plaster would. Wood also comes in different stains to give it a classier look. Certain stains may even cost slightly more than that. Polyurethane is a plastic-like substance that is often chosen for its flexibility.
However, it can get to be pretty heavy, and may require professional assistance. Polyurethane can be purchased with a faux wood stain or painted finish. Polyurethane foam looks like plaster, but is far lighter, making it a DIY-friendly choice. It is also relatively flexible. Flex is a flexible, rubbery material, making it a great choice for rounded walls. It usually requires professional installation, as it can be tricky to navigate curvy walls on your own while still getting an even finish.
There are ways to remove it relatively seamlessly, but the number of cracks and markings left behind will depend on the materials you used to originally install it. Removing the crown molding will be a time-consuming process, but if done with care and caution, you can minimize the damage done to both the molding and the wall.
With a sharp utility knife, cut at the point where the wall meets the crown molding. You will want to do this along the bottom as well as the ends.
0コメント